Recent Posts

Pages: [1] 2 3 ... 10
Bug Reports / Re: no CW TX PWR meter on K3
« Last post by w8rj on Today at 03:18:10 am »
It's really not a bug, it's just the way the K3 is. With the K3, the driver needs to poll the radio for power out and in CW the radio is in transmit for such a short time, it's just never read correctly. With the later model Kenwood's (including your 590), respond much quicker than the K3.
Bug Reports / no CW TX PWR meter on K3
« Last post by ok1dwq on Today at 12:54:08 am »

today I changed my old TS590s with new K3. But i have one issue during CW transmitte. No PWR and ALC meter is displayed. Does I have somewere mistake or it is issue of driver?
With SSB mode all is OK.

Bye Tom
General Support / version 9 and keyboard shortcuts for more blind accessibility
« Last post by n3ain on Yesterday at 04:45:05 pm »
When will version 9 be coming out with full accessibility for screen reader users? Its been talked about for a year now. We need more keyboard shortcuts to make this good software even better. Thanks and 73. Joe
General Support / Re: invalid password
« Last post by kc8wh on Yesterday at 12:05:48 pm »

Think I got it.

Requested permissions on your remote


Mike KC8WH
RCForb Server / Re: SPE Expert 1K-FA Support
« Last post by oh1bdf on Yesterday at 11:11:03 am »
Dear fellows,

today I managed to get the first version working based on modified 2K driver. Still missing ON/OFF support, but once I get it working, James said he will integrate it so that there will be a new Amp select option for <drum roll> Expert 1K-FA  :)

Stay tuned & 73
-petri OH1BDF

General Support / Re: Controls
« Last post by w8rj on Yesterday at 10:33:21 am »
1) Make sure the server is connected to a radio
2) Make sure there is only one instance of the server running (check the Windows tray)
3) Reinstall the Microsoft runtime 2010 C++ (X86)
4) Run the .NET repair tool from Microsoft
General Support / Controls
« Last post by sv8bur on Yesterday at 08:50:27 am »
 I am new onRCForb. I managed to setup the server, the question I would like to ask is:
I want to add controls in order to be seen on the client.
For example  on "The Allowed Sliders" I am pressing on "Get List" and I am getting nothing when I am pressing on the next button I am taking nothing too see the attachment
General Support / Re: Microham MK II and TS 480 issue
« Last post by va3sb on Yesterday at 05:24:46 am »
Good morning Roger.

Thanks again for your comments and suggestion. Looks like I won't be able to get it sorted out until possibly my next visit to the remote station.
In the meantime, I have re-installed my Signalink and have that working.

Thank you for your help and all of your work with RemoteHams. Greatly appreciated.

Have a nice day.

General Support / Re: Microham MK II and TS 480 issue
« Last post by w8rj on April 23, 2018, 08:41:26 am »
I assume you're getting RX audio from the data jack on the back of the radio. Look at Menu #047 (AF Output for Data Communications). Even though it says data communications, I would bet that menu will affect any RX audio out the data jack.

Also the slider in the server for RX level, if you get over half way on the setting the server will perform a boost in software.

Since RX audio is on a record device, check in the Windows controls on that device, and see if there is a boost setting.
General Support / Re: Microham MK II and TS 480 issue
« Last post by va3sb on April 23, 2018, 08:27:27 am »
Good day Roger and thank you for your usual prompt response.
I appreciate that you may not be familiar with the Microham MK II and thank you for your suggestions.

Just to be clear, on the dropdown menu in the server, I do see Input - Line (2-microHam CODEC) and Output - Headset Earphone (2-microHam CODEC) I have both of these selected in Server.
Unfortunately, I still cannot seem to get sufficient RX audio drive to the computer. Even though I have COM 16 selected for PTT. I am also unable to get the transceiver to go into transmit.

Will keep working on it. BUT if some one is using a microHam MK II i would greatly appreciate hearing from them. :-)

Thanks again.


Pages: [1] 2 3 ... 10